The 10 Best Analog Multiplexers to Buy – August 2022 Review

Looking for the best Analog Multiplexers?

We did 19 hours of research and testing 6 products to create this review. We believe the best Analog Multiplexers doesn’t have to be the most sophisticated to be exceptional. Our product selection lives up to its promise. Many different criteria were used for this comparison to be more relevant and more precise. Now discover our comparison !

TOP 10

No. 1
Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino
  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx).
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc.
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
No. 2
2CH AHD TVI CVI 1080p HD Video Multiplexer CVBS 2 Channel Video Coaxial Multiplexer for Hikvision Hdcvi 1080P 2MP CCTV Camera 2 Cameras by 1 Cable for CCTV Security System (2CH Multiplexer)
  • It supports 2 channel video signals in one coaxial cable by way of Frequency Division Multiplexing.
  • Perfect quality effect,support AHD/CVI /TVI up to 1080P;
  • Transmission only in one coaxial cable without any delay and interference. Saving the cost of the wiring.
  • Widely used in outdoor street, large factories, long distance transmission, etc
  • Package Content : 1 x multiplexer Transmitter;1x multiplexer Receiver;1 x Manual(NOTICE: DC12V 1A power Adapter No included)
No. 3
10 Pcs CD4051 DIP-16 Single 8 Channels Analog Multiplexer IC
  • CD4051 is 8-Channel analog multiplexer is digitally-controlled analog switches having low ON impedance and very low OFF leakage current
  • Package / Case: PDIP-16 , RoHS: Yes
  • Logic Types: MSI Functions-Decoders,Encoders and Multiplexers
  • package 10 pcs
  • Quality ensured , no-hassle refund if you are not 100% satisfied!
No. 4
HiLetgo CD74HC4067 CMOS 16 Channel 16 CH Digital Analog Multiplexer Breakout Module for Arduino
  • Function: Use 16 ADCs to collect 16 analog signals.
  • Use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels.
  • Analog output: DIG;Channel control: S0-S3
  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
  • This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.
No. 5
Bridgold 10pcs 74HC4051 74HC 8-Channel Analog multiplexer, Signal Splitter,16-DIP
7 Reviews
Bridgold 10pcs 74HC4051 74HC 8-Channel Analog multiplexer, Signal Splitter,16-DIP
  • Wide analog input voltage range: ± 5 V
  • Logic level translation: to enable 5 V logic to communicate with ± 5 V analog signals
  • Output capability: non-standard
  • Typical “break before make” built in
  • The products have been strictly screened, with stable performance and reliable data output.
No. 6
E-link 2CH CVI AHD TVI Coaxial Multiplexer, HD Analog Camera CCTV Video Multiplexer Over Single Coax Cable up to 1300ft
8 Reviews
E-link 2CH CVI AHD TVI Coaxial Multiplexer, HD Analog Camera CCTV Video Multiplexer Over Single Coax Cable up to 1300ft
  • Support 2 channel 1080P CVI/AHD/TVI Camera or Analog Camera.
  • Transmit Over SYV75-3 Single core coaxial cable.
  • Max distance: 1300 Feet (400m).
  • The HD multiplexer converter 2 video signals into digital signal and transmit over single Coax cable.
  • The CCTV multiplexer used for the locations that don’t have enough coaxial cable resource and projects need to save cost for cabling.
No. 7
DollaTek 3Pcs 74HC4051 8-Channel-Mux Analog Multiplexer Selector Module
  • The 74HC4051 is an 8-channel analog multiplexer/demultiplexer with 3 digital selects (S0-S2), one active low enable (E), and 8 independent inputs/outputs (Y0-Y7) ) and a common input / output (Z).
  • When E is low, one of the 8 switches will be selected by S0-S2 (low-impedance state). When E is high, all switches enter a high-impedance state, directly ignoring S0-S2.
  • VCC and GND are the supply pins for the digital control terminals (S0-S2, E). The VCC to GND range of the 74HC4051 is 2.0V-10.0V.
  • As a digital multiplexer/demultiplexer, the VEE will be connected to GND (typically grounded).
No. 8
NOYITO CD74HC4067 CMOS 16-Channel Digital Analog Multiplexer Breakout Module
3 Reviews
NOYITO CD74HC4067 CMOS 16-Channel Digital Analog Multiplexer Breakout Module
  • Function: Use 16 ADCs to collect 16 analog signals.
  • Use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels.
  • Analog output: DIG;Channel control: S0-S3
  • This is a breakout board for the very handy 16-Channel Analog / Digital Multiplexer / Demultiplexer CD74HC4067.
  • This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.
No. 9
12Pcs CD74HC4067 16-Channel Analog Digital Multiplexer MUX Breakout Board Module CD74HC4067 CMOS Precise Module Compatible with DIY
  • CD74HC4067 board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer, use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels; Analog output: DIG; Channel control: S0-S3
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc.
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to.
No. 10
Bridgold 10pcs CD4051 4051 CMOS Analog Multiplexers/Demultiplexers Single 8-Channel with Logic Level Conversion IC,DIP-16.
  • Wide Range of Digital Levels:Digital 3V to 20V
  • Low ON Resistance, 125Ω (Typ) Over 15VP-P Signal Input Range for VDD-VEE = 18V
  • High OFF Resistance, Channel Leakage of ±100pA (Typ) at VDD-VEE = 18V
  • Binary Address Decoding on Chip
  • 100% Tested for Quiescent Current at 20V

Intro

Find out where you can get the best Analog Multiplexers! Making your choice among different Analog Multiplexers on the market is not always easy. It can also turn into a daunting task because of the many websites offering the same type of product. On this page, we will give you a comparison to get the best value for your money. This complete ranking provides you with a comprehensive view and allows you to pick the best Analog Multiplexers. You will find a broad selection of models, brands, and prices. Whether you want to save money or find out what is the best Analog Multiplexers for you, our comparison will help you make the right choice. To keep things practical and easy to understand, we created a Top 10 of the best Analog Multiplexers. You won’t have to choose your products at random anymore.. On your marks! Compare! Pick your Analog Multiplexers!

Our Picks

No. 1
Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino
  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx).
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc.
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
No. 2
2CH AHD TVI CVI 1080p HD Video Multiplexer CVBS 2 Channel Video Coaxial Multiplexer for Hikvision Hdcvi 1080P 2MP CCTV Camera 2 Cameras by 1 Cable for CCTV Security System (2CH Multiplexer)
  • It supports 2 channel video signals in one coaxial cable by way of Frequency Division Multiplexing.
  • Perfect quality effect,support AHD/CVI /TVI up to 1080P;
  • Transmission only in one coaxial cable without any delay and interference. Saving the cost of the wiring.
  • Widely used in outdoor street, large factories, long distance transmission, etc
  • Package Content : 1 x multiplexer Transmitter;1x multiplexer Receiver;1 x Manual(NOTICE: DC12V 1A power Adapter No included)
No. 3
10 Pcs CD4051 DIP-16 Single 8 Channels Analog Multiplexer IC
  • CD4051 is 8-Channel analog multiplexer is digitally-controlled analog switches having low ON impedance and very low OFF leakage current
  • Package / Case: PDIP-16 , RoHS: Yes
  • Logic Types: MSI Functions-Decoders,Encoders and Multiplexers
  • package 10 pcs
  • Quality ensured , no-hassle refund if you are not 100% satisfied!

Why you should trust us?

This guide is the result of more than 10 years of experience in researching, testing, and writing about various subject. Our team members are experts in their fields. We spent 19 hours reading all the articles we could find online and all the customer reviews on various retail websites such as Amazon, Ebay, Alibaba or Flipkart. We also found many websites that provided valuable resources such as purchasing guides and detailed information on Analog Multiplexers. To help you make the best choice among the hundreds of products available, we decided to offer you a comparison in order to find the best value for your money. We searched different fields to find the best Analog Multiplexers. We also looked at the best alternatives for reasonably priced and easy to use products. After we determined our main parameters, we conducted our research and tests.These parameters separate a great product from an average one:

  • Price
  • Ease of use
  • Customer reviews
  • Quality
  • Durability

Conclusion

We hope this ranking was helpful to you in choosing the Analog Multiplexers that best suits you. We made it thoroughly and we will update it regularly, so that you get a real-time comparison. Our goal is to allow you to compare models and prices, to get an overview of what the market has to offer. We are here to make it easier for you and to make informed decisions. If our ranking gave you a clearer view on the different products available, feel free to let us know in the comments section. We will happily read them.

Click to rate this page !
Thanks !

Last update on 2022-08-16 at 01:26 / Affiliate links / Images from Amazon Product Advertising API